Видео

I didn’t get a spacer that fits the right screw

I was a roll tender for a few years in the early 80s. It's dirtiest, most toxic job in printing. Spent the rest of my career in the prepress department on the stripping table and Mac.

I always wondered if the Gearwrench ratcheting wrenches that pivoted like that ratchet, also could be used loose like you demo’d

So, to reduce the water pressure (from 105 to 80), we turn the screws counterclock, correct? I have the NR3XL 15-75. Does that mean that if the water from the city comes at 130 this one can't reduce it beyond to after 75? Do I need a bigger PRV i.e 130? If there's another faucet open, the presure come down to like 40. But if I only open one bib it says 105. Am I missing something here.

Tengo uno totalmente igual y dejo de funcionar el teclado de stars

i wonder if you put the nut on loose, allowed it to tac up, then ball it up under torque would that be better?

Were the nuts and bolts super clean before you started?

I don’t like cruise control I think it creates a problem that would not be there otherwise

Does this apply to a 2.7l

I don't understand how the 271 is supposed to prevent tampering (per Loctite) when it comes off with such little torque.

Awesome mate.Thanks

Great stuff, thank you.

Thanks!

How did you connect the oscilloscope? Directly to ground and mains? Does this voltage not destroy the oscilloscope without any wall wart between? I would like to test my diesel power generator but I'm not sure how to connect the oscilloscope without destroying it.

271 is also a sealer and works to higher temps than 243.

Amazing video. Thank you for posting. I am staring at the instructions for this microwave and was very confused lol

Thank you

What happened the right cam was off by a couple of teeth?

Thank you! I started reading the instructions and got so confused 😂 I have been putting off switching mine out because of it

Thank so much! Installed this very unit while ignoring the instructions thanks to your informative vlog and it was so easy!

The filter over each electric motor fan air intake doing their job.

You work too hard man . I work at newspaper company , I’m a helper but only need glue the roll and hang plate . Have paper handler pick all bad paper for recycle. General worker pick up trash and dirrty rag .

Thanks a ton for this video - about to install the one my wife just picked up and if gives me a bit of a head start

Loctite 290 3* more that blue, i think.

Get / make spacers for the castors if you want it taller. Excellent chest. Congratulations

Great video man !!! You fixed my car for me and didn't even know you did, thanks for great explanation of the process

Excellent demo. As a Harley Davidson enthusiast I need to use locktite.

You answered all the questions we couldn't figure out by staring at the manual, lol. You absolutely saved us a huge amount of time and headache, thank you thank you thank you! 🎉

This was very helpful! Thank you!!

Was this on a Mustang? I was a bit confused on what appears to be for something to be inserted on the hinge area, kind of star shaped opening - what is this for?

I was so afraid to do this myself. I don’t need special gloves? 🧤 I just KNEW I would get shocked. lol

Thank you!! I tried so many bots, this is so simple.

Tesekkurler

When I had to reposition a full roll I used some of the brown wrapper and folded it into a small square so it was about a half inch thick , then I pushed the roll onto it and then you are able to swivel the roll in any direction with ease.

why didn't you use the red wire?

10:12 washer power on sound on a microwave???

Bookmark this bolt for myself 38:59

Thank you. This made it a snap

Great video

Nice video I'm a retired Electrician used thread locker a bit through my career not as much as you have. I just want to know when the hell did you steal my deep well socket it has to be mine it has 3 hash marks on it! That is how I marked all my tools with a file or 3 dots with a punch when I seen your tool mark I just thought I'll be damn.

Would a Ryzen 5 5600x work with this motherboard

When you shut off the water, did you have to do anything to the hot water tank

aynı kasalardan şuan bende de var. haf 942 yan kapak pencere olarak modifiye yaptım. ama yıllardır kullandığım haf 942,den sıkıldım. 2 gün önce haf 700 evo aldım. fakat henüz kurma vaktim olmadı. kurulum için sabırsızlanıyorum.

Hi! We hired someone to install our new ceiling fan same model in this video. However, it seems to spin wobbly when set to spin forward, but it seems to work fine when we set it to spin in reverse. Is it due to wrong installation or is my new ceiling fan faulty? Thank you in advance!

Nice Transformer Buzz in the background! Lol!

Not very practical now is it.?

Why would you run UF through your wall cavity? No bueno. Other than that bit of homeowner hack nice work.

How to sort out to the use of type-c in the front panel? I have the same board with the with corsair 4000d airflow case. At the time i didn't think it would be handy be thinks changed.

Hopefully someone can help me with the question. I have a similar unit and they give instructions for cabinet depth between 12 and 15 inches my cabinet is 16 inches and my concern is that the top cabinet up at the front is going to cover the vent holes. They say to make sure you don't cover those vent holes so it seems like I need to put some kind of a blocking on my back wall to bring the microwave out so it's going to stick out about 2 inches so the vent is clear. But I noticed your unit only sticks out about an inch, which means your vent is covered. Has that been a problem?

Hey, just installed ryzen 7 5700x on the strix b559 f wifi MB. I can't get win11 to install. Something with Tpm. What did you do?